15
Sep
Horrible valve train noise after reinstalling heads PLEASE HELP. 53021556AA 8x Exhaust Push Rods.
Please check local and State laws for emissions compliance before purchasing this product.
Replace 57 hemi push rods. I have a 2006 Dodge Ram 1500 with a 57 liter hemi. I just replace the lifters and push rods and put everything back - Answered by a verified Dodge Mechanic. We are replacing all 8 pistons in our 57 hemi and gapping piston rings.
We go into depth on how to Heat and press the wrist pins out of the heat pressed con. Yeah I have a 260 cam and Ive had some valve-train noise getting slowly worse since the cam and heads install ported heads w 61 springs. The installer did not use the propper assembly lube on the pushrods during the install so I believe I might have some wear causing the noise.
In this video I diagnose my 57 hemi with a bad lifter and camshaft we replace the lifters with hellcat lifters and replace camshaft with a greene racing 5. It probably makes sense to replace all of the bolts while youre in there. This can run about 100 for the parts.
Some opt for aftermarket exhaust manifold to prevent the warping. Ultimately if the manifold itself is warped then it will continue to cause premature failures of replacement bolts. 3 57 HEMI Multi-Displacement System MDS Issues.
57 Personal Best. Heads Cam and Spray - 1146 w 159 60 61 Personal Best. Forged Novi 1500 and Spray - 10405 1566 60 12969 74 Personal Best.
Aluminum 449 - 10736 ET 1589 60 12505 MPH NA 70 Personal Best. Iron 426 - Whipple 29 - 1046 so far. Amongst the core NA blocks the 57 is actually a stouter block capable of more significant power adder upgrades before having to beef up the bottom end than you would have to do with the 62 or the 64.
If you decide to beef up the bottom end the 57s are capable of exceeding Hellcat power levels - and by quite a lot. Flow test your suspect cylinder since a compression test is out f the question due to bent push rods pressurize the cylinder with a air blow gun with a rubber tip to seal the spark plug hole. Apply full air press and listen for air either coming out of the exhaust or intake Do this with the push rods removed so valves are fully closed.
As far as cost its about 30 different plus the time to custom make the initial one and mail it away and then get the small tipped Desoto hemi pushrod custom made to your initial one. Also having adjustments can help for high rpms as a 14 turn preload will rev higher than 34 turn preload without valve float. Dodge 57 Hemis Ticking This is for ALL the Dodge 57 Hemi Engines that are ticking like a junker driving down the road and DodgeChrysler and most service dealers WONT HELP.
There are a lot of 57 Hemi engines out there with a very bad tickingclacking noise coming from their engines that is heard INSIDE the car while driving 1500-1800 rpms and higher. Horrible valve train noise after reinstalling heads PLEASE HELP. Check recheck then triple check feel that every push rod is in and seated.
If you dont have the miller pushrod alignment tool for the intake side it can be a real PITA to get it right. Once done have a bud get in put the gas pedal to the floor and. Arrington SR-2B Camshafts and Push Rods.
Arrington High Performance HEMI Camshafts Arringtons line of high performance camshafts for your 57L or 61L Dodge Chrysler or Jeep HEMI engine are dyno proven to increase a 57 motor to 3344 horsepower and 3439 ft-lbs of torque from an otherwise stock engine with basic tuning. I am rebuilding a 2003 dodge hemi 57 and would really like to put roller tip rockers and ideally even roller needle bearing rockers. I was very surrised to see a totally mechanical rocker.
Answer 1 of 7. Yes Looking right now on the dodge website I see that the 57-Liter V8 Hemi has VVT which is short for variable valve timing. Dodge does not say that the engine is a pushrod engine.
Most of the time in pushrod engines one cannot. 8x Intake Push Rods. 53021556AA 8x Exhaust Push Rods.
53021557AA 2x Yoke wLifters. 53021728BC 1x EGR Tube Seal. 4591250 20x Head Bolts.
6506334AA Here are the quantities and corresponding part s for your current list. Id recommend Andy East Coast Moparts Supporting Vendor their prices can rarely be beat. Chrysler Dodge 57 61 62 64 Hemi Connecting Rods.
Molnar Technologies H Beam Gen 3 Hemi rods for the 57L 61L 62L and 64L engines are machined from billet 4340 steel and then heat treated to provide improved strength. To make the rods even stronger they are shot peened to which also increases fatigue life. 04 57 hemiit keeps bending intake push rodsvalves are all freealso a popping noise that sounds like out the exhaustI just saw to look for exhaust manifold bolts that are loose or brokethat certainly could cause the noise in the exhaust but not the bent push rodsalso my local parts store has 25 push rods as a stocking quantity so that tells me its a common issue.
MOPAR Heavy Duty Gen3 HEMI Lifters OE Replacement or MDS Delete Kit Qty 16 57L 61L 62L 64L HEMI Engines MSRP. Remove rocker arm assembly and push rods. Identify push rods to ensure installation in original location.
Remove the cylinder head. Remove bolt from tappet guide holder. Remove tappet guide holder.
Pull tappet out of bore with a twisting motion. I like the 57 better than the 64. It will take more of a beating and responds great to bolt ons.
Why do you think dodge offered the kits to upgrade the 57. Cost was too much to make it a way to go. You can spray more or boost more on 57 pistons.
Valve train is the weak link. Change the cam out and you can wake up a 57. 57L HEMI Forged 2618 Drop In Pistons and Rods Power Package.
E-mail this product to a friend. Please check local and State laws for emissions compliance before purchasing this product. U kinda tried to film how to install the pistons on the hemi engine.
Sorry for the quality cuz was done with my phone lolMy IG. 13b_dorito Here is some usef. Installing 57 Pistons and connecting rods.
Jump to Latest Follow 1 - 2 of 2 Posts. Joined Jan 20 2015 448 Posts. Discussion Starter 1 Apr 12 2015.
I am at the point of putting the engine back together and want to make sure I have the pistons and rods.